冷再生施工和机械租赁业务
筑路架桥,奉献社会;以人为本,不断创新

服务热线

18264104888

新闻中心

首页>>新闻中心平地机出租整机保养检查工作!

平地机出租整机保养检查工作!

来源:http://www.tclqgc.com/ 日期:2021-10-11 发布人:
平地机是利用刮刀平整地面的土方机械。刮刀装在机械前后轮轴之间,能升降、倾斜、回转和外伸。动作灵活准确,操纵方便,平整场地有较高的精度,适用于构筑路基和路面、修筑边坡、开挖边沟,也可搅拌路面混合料、扫除积雪、推送散粒物料以及进行土路和碎石路的养护工作。平地机在工程中使用较多,下面我们一起了解一下平地机整机保养检查工作。
Grader is an earth moving machine that uses a scraper to level the ground. The scraper is installed between the front and rear axles of the machine and can lift, tilt, rotate and extend. Flexible and accurate action, convenient operation and high accuracy in site leveling. It is suitable for building subgrade and pavement, building slope and excavating side ditch. It can also mix pavement mixture, remove snow, push granular materials and maintain earth road and gravel road. Graders are widely used in engineering. Let's learn about the maintenance and inspection of the whole grader.
1、平地机在使用施工前应对整个的机械进行的检查,了解整个平地机机械的构造。
1. Before using the grader for construction, the whole machinery shall be comprehensively inspected to understand the structure of the whole grader machinery.
2、刀轴应每日检讨,假如上面的槽磨出越过了刀轴直径25,就会转变。另外,刀轴的运用寿命是钨钢铣刀的半衰期。从广场区域,其性命,龙门铣床5毫米的深度约350-500。但是,有许多因素会影响刀轴的运用寿命,因而每日审查;
2. The cutter shaft should be reviewed every day. If the groove above is grinded beyond the cutter shaft diameter of 25, it will change. In addition, the service life of the cutter shaft is the half-life of the tungsten steel milling cutter. From the square area, its life, gantry milling machine 5mm depth is about 350-500 square meters. However, there are many factors that will affect the service life of the cutter shaft, so it is reviewed daily;
3、4个小时每次运用后光滑的轴承光滑脂。光滑的脂肪、车削和铣削滚筒在玩,在一切轴承油脂涂层;
3. Smooth bearing grease after 4 hours of each application. Smooth fat, turning and milling rollers are playing in all bearing grease coatings;
4、平地机的主要的义务是由铣刀,轴承、垫圈、铣鼓,由于长时光的操作历程和路面摩擦,可以更好的延伸机器的运用寿命;
4. The main obligation of grader is to use milling cutter, bearing, washer and milling drum. Due to long-time operation process and road friction, it can better extend the service life of the machine;
5、每次操作前用肉眼检讨机:一切紧固件可以收紧?能否有主要部件磨损或裂纹吗?石油供给石油可以实现?可以检讨轴承,检讨掩护盖,等;
5. Check the machine with the naked eye before each operation: can all fasteners be tightened? Is there any wear or crack on the main parts? Can oil supply be realized? Can review bearings, review covers, etc;
6、每次操作前检讨平地机,以及平地机出租都可以局部紧固件松(一个松懈的必要收紧)
6. Review the motor grader before each operation, and the motor grader rental can loosen the local fasteners (a loose necessary tightening)
7、每次把平地机出租机支配,检讨刀轴和轴承。假如涌现磨损的轴向地位,您须要更改新的,转变轴的轴承在同一时光。
7. Each time the grader is controlled by the rental machine, review the cutter shaft and bearing. If there is wear in the axial position, you need to change the new, change the shaft bearing at the same time.

阅读/ Recommended reading

1. 准备工作:使用者需要对水泥撒布车进行检查和维护,确保其正常运行。包括检查机械部件是否完好,油液是否充足,车辆的操作系统是否正常等。1. Preparation work: ...

冷再生基层工程质量检测、控制及注意事项 2024-03-20
公路路面养护冷再生知识汇总 2024-03-17
公路路面养护冷再生的施工要点 2024-03-17
冷再生机的控制要点要注意什么? 2024-03-13

产品/ Recommended products